Showing results: 391 - 405 of 770 items found.
-
HA4600/IF -
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA4600/IF series, is narrow-band multiplexing EDFA suitable for L-Band fiber link application. With build-in 1550nm Internal Modulation SAT-IF optical transmitter, used for inter-cutting DBS. The WDM inside will multiply the signal from TX and main line signal that is inputted from outside, then the combined signal will enter EDFA to be amplified to serve the local subscribers. To avoid the interferes caused by mismatching of the optical output power between TX and main line signal from outside, output power of the TX can go through a VOA, thus, it can be adjusted or set from the front panel. This unit is simple and clear, easy to be installed and tested. It offers a high quality and cost-effective solution for inter-cutting DBS into full optic relay 1550nm fiber CATV system and second-stage service area.
-
ICS Electronics
All of ICS's GPIB Digital Interfaces are user configurable and let you transfer data as bits, bytes or as strings of bytes. All data lines are high power TTL outputs or floating inputs with pullup resistors for sensing CMOS signals or switch contacts. All interfaces conform to the IEEE-488.2 Standard and are HP-IB compatible.
-
ICS Electronics
All of ICS's Serial Digital Interfaces are user configurable and let you transfer data as bits, bytes or as strings of bytes. All data lines are high power TTL outputs or floating inputs with pullup resistors for sensing CMOS signals or switch contacts. All interfaces conform to the IEEE-488.2 Standard and are HP-IB compatible.
-
Amphenol RF
Amphenol RF offers a growing Attenuator product line to meet your attenuation needs. Amphenol RF attenuators are designed to offer flat attenuation over the designated frequency range and feature a microwave grade resistor that consistently reduces power. Hex flats on the body allow this attenuator to be easily torqued to the mating connector.
-
6U VME430 6021 -
W-IE-NE-R, Plein & Baus GmbH
The WIENER VME 6021 crate series is the newest generation of 19" integrated packaging system according to the CERN VME430 standard. Designed primarily for applications in nuclear and high energy physics data acquisition, beam line control and test instrumentation it combines superior mechanical quality with lowest noise power supply technology.
-
Axiomtek Co., Ltd.
Axiomtek offers various kinds of backplanes for industrial computing platforms, including PICMG 1.0 PCI, PICMG 1.0 ISA, PICMG 1.3 full-size, and PICMG 1.3 half-size backplane. Axiomtek's backplane product line provides not only the highest compatibility with power supply unit but also the best choice of slot expansion.
-
TC-TP1 -
TRENDnet, Inc.
TRENDnet´s TC-TP1 is an easy-to-use amplified inductor and tone probe that is used for tone tracing and line testing. The TC-TP1 features a simple push button that provides easy operation and conserves battery power. This ergonomically designed device comes with adjustable volume control and signal LED for enhanced accuracy in noisy environments.
-
4U 32HP -
Kontron
As the established PICMG 2.0 CompactPCI has evolved, so has Hartmann Electronic’s product line. The 4U cPCI 4 slot solution is designed with quality and versatility in mind. This chassis comes complete with a 3U, 4 slot PCIe Gen3 backplane with full mesh topology, powered by a 180W ATX power supply.
-
8063 -
ICS Electronics
* Same Digital IO lines as standard 8063. * Same data transfer capabilities as standard 8063 * Digital I/O uses high-density DC-62 connector.* Power connections via 2 screw terminal strip or solder pads.* User configured IDN message and webserver pages makes board respond as part of your system.* Use an ICS Wiring Kit to extend the Ethernet signal to a rear panel RJ45 jack.* Runs on 9 to 32 Vdc power.
-
9005 UO -
Standard Electric Works Co., Ltd
● Maximum testing current of 5A ● Ranges: 2000μΩ / 20.00mΩ 5A 20.00mΩ / 200.0mΩ 1A 2.000Ω / 20.00Ω 100mA 200.0Ω 10mA● Maximum resolution of 1μΩ at 5A● Four terminal measurement● 4 Lines × 20 Characters LCD ● Memery function (200 measurement results)● Auto power off● Low battery indication● Power source: 1.5V "C" alkaline battery × 8● Safety Standard: EN 61010-1 CAT III 300V EN 61326-1
-
Stefan Mayer Instruments
Hand-held instrument for precise measurement of weak magnetic field from 0.1 nT to 200 µT (DC to 1 kHz). Typical applications are: Measurement of the Earth's magnetic field vector components, detection of AC fields from power lines, paleomagnetic investigations, package inspection according to IATA 953, and residual field measurement.
-
DS Series -
Taylor Dynamometer, Inc.
Similar in design to the DX Series, Taylor Dynamometer’s DS Series Water Brake Engine Dynos DS dynamometers bring you proven durability. In addition, this line provides increased power capacity – from 2,125 hp up to 4,250 hp (1,584 kW up to 3,169 kW) – thanks to larger diameter components.
-
9U VME430 6021 -
W-IE-NE-R, Plein & Baus GmbH
WIENER VME 6021 crate series is the newest generation of generation CERN VME430 compliant VME crates for large size 9Ux400mm cards. Designed for applications in nuclear and high energy physics data acquisition, beam line control and test instrumentation it combines superior mechanical quality with lowest noise power supply technology.
-
Tel-Tru® Manufacturing Company
Tel-Tru pressure gauges are available in a wide variety of dial sizes, accuracies, pressure ranges, and case configurations, for the various requirements of industrial and process instrumentation. Rugged features make the line of stainless steel gaugesa top choice for process, power, hydraulic and OEM markets. All Tel-Tru pressure gauges meet ASME B40.1.
-
XG-8000 series -
Keyence
Offering a lineup of up to 21 megapixel area cameras and 8K line scan cameras, the XG Series contains powerful vision system technology providing flexibility and power to solve a wide range of applications. No experience required to select lighing! - newly-developed, revolutionary Lumitrax function. Powerful Vision Software. Flexible Multi-Camera Hardware.
